Building Smarter Outdoor Living Spaces: A Contractor's Guide to Audio, Lighting, Wi-Fi, and Security
The best outdoor living spaces work as well as they look. Here's how Central Oregon contractors can plan the technology before construction makes it hard and expensive to add.
The covered patio is done. The outdoor kitchen is in, the pavers are set, the landscaping is finished, and the homeowners are ready to enjoy their new backyard.
Then the question comes.
"Can we add speakers around the fire pit? And better Wi-Fi out here? What about a camera by the gate?"
All reasonable. But now you're cutting into finished surfaces, hunting for power, trenching through new landscaping, or compromising details your crew spent months getting right.
Most of that is avoidable with one conversation during design.
For contractors building in Bend, Sisters, Sunriver, Redmond and across the region, outdoor technology deserves the same early attention as electrical, plumbing and HVAC. We help builders plan outdoor technology installation in Central Oregon from the first set of drawings, so the finished space does what the homeowner pictured without rework.
(Homeowner looking for ideas? Our guide to outdoor entertainment systems for Central Oregon backyards is written for you. This one is for the people building the space.)

Outdoor living changed. Planning should too.
Today's outdoor spaces often include full kitchens, covered entertaining areas, hot tubs, fire features, outdoor TVs and designed landscape lighting. Homeowners want the same convenience outside that they have inside:
Music that follows them from the kitchen to the patio
Landscape lighting that comes on at sunset without anyone touching a switch
Reliable Wi-Fi at the outdoor kitchen, the hot tub and the detached shop
Cameras watching the driveway, gates and entrances
Simple controls for all of it
Each one sounds simple on its own. Together, they take coordination between the builder, electrician, landscape contractor and technology integrator. Whether you get a clean install or a frustrating retrofit usually comes down to when technology enters the conversation.
1. Outdoor audio: design for the whole space, not just the patio
Two speakers under the patio roof might cover the dining table well. But the fire pit is 40 feet away, and that's where everyone ends up after dinner.
Turning it up isn't the answer. It makes the sound uneven, bothers the neighbors, and blasts whoever is sitting closest to the speakers. On a quiet Central Oregon evening, sound carries further than people expect.
Plan around listening zones
Good outdoor audio starts with where people actually spend time: covered patios, outdoor kitchens, hot tubs, fire pits and landscaped seating areas.
We design outdoor systems on Sonos, with weather-resistant speakers placed for the space and amplification matched to it. Speakers can tuck under rooflines or sit in the landscaping, which spreads sound evenly at a lower volume. A Sonos Amp ties wired outdoor speakers into the home's Sonos system, so music runs inside and out from one app. For larger yards with several distinct areas, Sonos Amp Multi (available only through installation partners) can run up to four independent zones from a single unit in the equipment rack.
What to plan before construction
Set speaker locations while the patio structure and landscape layout are still on paper.
Route speaker wire before soffits close, ceilings are finished and hardscaping starts.
Find a protected location for amplifiers, indoors or wherever the manufacturer allows. Outdoor-rated speakers don't mean the electronics powering them belong outside.
If landscape speakers are part of the design, get underground pathways in before irrigation, retaining walls and pavers.
Builder takeaway: planned outdoor audio sounds more even, installs cleaner and respects the architecture.
2. Lutron lighting: make the space work after sunset
Outdoor living here doesn't stop when the sun goes down. Good lighting makes a patio welcoming, picks out the architecture, lights the walkways and sets the mood. But installing outdoor lights and designing an outdoor lighting experience are two different things.
Think in scenes, not switches
With Lutron lighting control, compatible exterior circuits and fixtures become part of one coordinated system. Instead of a bank of switches by the back door, the homeowner taps a scene:
Entertain: patio lights dim to a comfortable level, landscape accents come on, and walkways stay softly lit.
Evening: architectural and landscape lighting warm up as daylight fades.
Goodnight: decorative lighting turns off, while selected path and security lights stay on.
Lutron can also run schedules tied to sunrise and sunset, so the lights follow the seasons instead of a timer someone has to reset every few months.
Why coordinate early
The electrician and the integrator need to agree on lighting zones, compatible dimming, control locations and the electrical infrastructure behind them. Decide where controls go, which fixtures sit under patio covers, and how landscape lighting will be fed and controlled.
Settling that before electrical rough-in prevents late changes to switching, circuits and finished surfaces. It also keeps controls discreet instead of adding switches after the design is done.
Design for dark skies
This matters more here than almost anywhere. Sunriver became Oregon's first International Dark Sky Place in 2020. Deschutes County updated its outdoor lighting ordinance (DCC 15.10) in 2025: in the unincorporated county, replacement fixtures installed on or after December 23, 2025 must comply, and all other fixtures have until December 23, 2028. Bend, Sisters, Redmond and the other cities set their own standards.
Shielded, downward-aimed fixtures and a Goodnight scene that turns decorative lighting off at bedtime keep a project on the right side of the rules and the neighbors. Confirm the requirements for your jurisdiction before fixtures are ordered.
Builder takeaway: design the lighting experience first, then coordinate the fixtures, circuits and controls around it.
3. Outdoor Wi-Fi: the foundation nobody sees
A beautiful outdoor space isn't much fun if the music keeps dropping or the homeowner's phone loses Wi-Fi at the back door.
A strong network inside doesn't mean good coverage outside. Exterior walls, stone, metal siding, insulated glass, distance and landscaping all weaken the signal. On larger Central Oregon lots, the outdoor living area may sit well beyond the reach of any indoor access point.
Design the network around the property
Instead of hoping an indoor router reaches the back fence, design coverage for the places it matters: the patio, outdoor kitchen, hot tub, detached garage, guest house and gathering areas.
We build networks on eero, including outdoor access points where they fit. The eero Outdoor 7 is made for exterior mounting, is rated against dust, rain and snow, and is tested to operate from -40°F to 131°F. It runs on PoE+, so one Ethernet cable carries both power and data. When it's practical, a wired connection to the outdoor access point is far more dependable than asking a wireless signal to push through an exterior wall.
What builders need to know
Talk about outdoor Wi-Fi before exterior finishes and landscaping are complete.
Identify likely access point locations, get cable to them, plan the mounting surface, and leave room for network equipment inside the home.
Detached shops, guest houses and the far corners of acreage may need longer runs or conduit trenched during sitework.
On rural properties using Starlink, plan where the dish mounts and how its cable reaches the equipment closet at the same time.
Planning early avoids surface-mounted cable, compromised device placement and digging up the yard later. For the inside of the house, see our guide to new construction Wi-Fi planning for builders.
Builder takeaway: reliable outdoor Wi-Fi is infrastructure, not an accessory. Design it before the exterior is finished.
4. Security cameras: plan coverage before the exterior is final
Cameras are another feature homeowners often ask for after the fact. The best camera locations are rarely easy to reach once siding, stonework, roofing details and landscaping are complete. A camera mounted wherever power happened to be usually doesn't see what the homeowner needs.
Start with the property's priorities
Think about how people and vehicles move around the property. On a Central Oregon home, priority areas often include:
Driveways and vehicle entrances
Front doors and main entry points
Side yards and pedestrian gates
Detached garages, shops and storage
Rear entries and outdoor equipment areas
We install surveillance on Alarm.com, whose video analytics on supported cameras can tell people, vehicles and animals apart, so alerts are worth reading. A homeowner probably wants to know when someone walks into the side yard. They don't need a notification every time a deer crosses the lot. The right camera, placement and detection zones make that possible.
Early coordination gets better results
Review camera locations alongside the exterior elevations, lighting plan and landscaping during design. That's when you settle mounting heights, viewing angles, and the power or network connection each camera needs. Hardwired cameras typically run on Ethernet with Power over Ethernet; others need separate power or Wi-Fi. Requirements vary by camera.
Watch for architectural lighting shining into the lens, reflective surfaces, trees that will grow, and the neighbors' privacy. A beautifully concealed camera isn't useful if a future pergola beam or a mature pine blocks its view.
In jurisdictions that have adopted the wildfire-hardening code (R327), the eave and soffit are a rated assembly, so camera penetrations need to be detailed before the soffit closes. Our security pre-wiring guide for contractors covers that, and our security camera placement guide covers coverage in more depth.
Builder takeaway: design cameras for the coverage the homeowner needs, then plan the wiring and mounting to support those views.
5. The biggest opportunity: coordinate everything before hardscape and drywall
Outdoor technology touches several trades and several milestones. Speaker wire passes through framing. An access point needs Ethernet behind a finished exterior wall. Landscape lighting and speakers need sleeves in place before concrete is poured. Without coordination, even small additions become disruptive.
Phase 1: Design and pre-construction
Identify the outdoor living zones and what the homeowner wants in each. Set preliminary speaker locations, lighting zones, camera views, Wi-Fi coverage, equipment space and control preferences. Review them against the architectural drawings, electrical plan and landscape design.
Phase 2: Rough-in and infrastructure
Before framing is covered and exterior finishes go on, complete the cable runs, electrical provisions, mounting prep and conduit. Outdoors, that often means sleeves under future hardscape, weather-rated cable and enclosures, and pathways to landscape features. Call 811 before anyone digs.
Electrical and low-voltage work should be done by the appropriately licensed trades, to code and to manufacturer requirements. (Our guide to what to prewire before drywall covers Oregon's permit and inspection basics.)
Phase 3: Installation, testing and handoff
Once construction and landscaping are far enough along, install and commission the equipment. Walk-test the Wi-Fi where people will actually sit, check every audio zone, fine-tune the lighting scenes, and confirm camera views after permanent landscaping and exterior lighting are in.
Finish with homeowner training, so the clients know how to use what they paid for.
The goal is simple: technology should feel like part of the finished home, not something added because it was forgotten.
Where we'd tell you to skip it
Not every outdoor space needs every system. Here's where we'd hold back.
A small patio doesn't need landscape speakers. A pair under the roofline covers it.
Don't light everything. Fewer, well-placed, shielded fixtures look better and sit comfortably within Central Oregon's dark-sky rules.
Don't buy the hardware at framing. Buy the pathways now. Conduit and cable keep the options open; equipment choices can wait until the space is nearly finished.
Don't add an outdoor access point because it sounds good. If the patio already walk-tests well, leave it.
A contractor's outdoor technology pre-construction checklist
Before finalizing your next outdoor living project, ask:
Have we identified every outdoor entertainment and gathering area?
Are speaker locations and audio zones on the plans?
Have exterior lighting zones, controls and scenes been discussed, including local dark-sky requirements?
Will the Wi-Fi network cover the outdoor areas people will actually use?
Are camera locations based on the coverage needed, rather than convenient wiring?
Have conduit and cable routes been coordinated before concrete, pavers and landscaping?
Is power available where it's needed?
Is there accessible, protected space for network and audio equipment?
Have the electrician, landscape contractor and technology integrator reviewed where their work overlaps?
Is there a plan to test and commission every system before the homeowner moves in?
You don't need every product picked before framing begins. You do need an infrastructure plan that keeps the homeowner's options open.
Why Central Oregon projects need extra attention
Our climate is hard on outdoor equipment: intense summer sun, hard freezes, snow, dust and big temperature swings between day and night. Speakers, cameras, access points, cable pathways and electrical components all need to be rated for where they're installed. Placement should account for snow sliding off roofs, runoff, afternoon sun and future maintenance access.
Many properties in Bend, Sunriver, Sisters and the surrounding communities also have larger lots, detached structures, and entertaining areas well away from the main house. Those layouts create networking and wiring challenges that are far easier to solve during construction than after.
The best outdoor technology plan isn't the one with the most equipment. It's the one designed for the property, the architecture and the way the homeowner will use the space.
Common questions
When should a contractor bring in a technology integrator on an outdoor living project?
During design, before electrical rough-in and before any hardscape or landscaping is installed. That's when speaker locations, lighting zones, access point locations, camera views and underground pathways can be planned without cutting into finished work.
Can outdoor speakers connect to the home's Sonos system?
Yes. Wired outdoor speakers can connect to the home's Sonos system through a Sonos amplifier, so music can play inside and out from the same app. The amplifier should live in a protected location, not outside with the speakers.
Does a strong indoor Wi-Fi network cover the backyard?
Often not. Exterior walls, stone, metal siding, insulated glass, distance and landscaping all weaken wireless signals. Larger properties and detached structures usually need an outdoor access point, ideally wired back to the network, to get reliable coverage where people actually sit.
Do outdoor lighting rules in Central Oregon affect landscape lighting design?
Yes. Deschutes County updated its outdoor lighting ordinance in 2025, and cities such as Bend set their own standards. Shielded, downward-aimed fixtures and scenes that turn decorative lighting off at night help a project comply. Confirm the requirements for your jurisdiction before ordering fixtures.
Build it right the first time
Exceptional outdoor spaces come from good design and coordinated craftsmanship. Technology should support that work, never compete with it.
We work with custom home builders, general contractors, architects, electricians and designers throughout Central Oregon to plan outdoor audio, Lutron lighting control, networking and Wi-Fi, surveillance and smart home systems from the first set of drawings. Whether it's a covered patio in Bend, an entertaining area in Sunriver or a custom property near Sisters, we'll help you get the infrastructure right before construction makes changes harder.
Your team builds the space. We'll make the technology work beautifully within it.
Planning an upcoming project?
Bring us in before your next rough-in, concrete pour or exterior finishing milestone. Send us the drawings, and we'll mark up where audio, lighting control, Wi-Fi and cameras need pathways, at no cost.
Call (541) 241-8114. We'll take care of it.




Comments